This DIY coffee table was inspired by a West Elm find for $999 – except we made our version for less than $50 using pallet wood. It’s easy to do!
Sometimes you see a piece of furniture in a catalog you HAVE to have (remember my DIY outdoor bench?). You know what I’m talking about, right? For us it was a West Elm Plank Coffee Table, with the price tag of $999. But then we realized something – we could make our own DIY coffee table, for a lot less, out of pallet wood.
We’ve worked with pallet wood before, but this was the biggest project we decided to tackle with it. The good news? It wasn’t as hard as we thought . . . and this DIY coffee table ended up being less than $50 to make! $45 total.
West Elm Coffee Table
To give you a frame of reference, this is the table on the West Elm site that we liked:
Find it here listed for $999. We weren’t about to be intimidated by a table and we knew we could make a DIY coffee table ourselves! Here’s how we made ours.
How to Make a Coffee Table
The finished dimensions of this table are 16″ tall x 30″ wide (square).
Gather These Supplies
- 3 – 4 old pallets – let pallet wood sit for several weeks before using (see first step); see Cut List for how to cut the pallet wood
- 4′ x 4′ piece of pine plywood – (cut to 30″ x 30″, see Cut List)
- 2″ x 2″ x 8′ lengths of pine (4) – (4 are cut to 27″, 8 are cut to 30″, see Cut List)
- 2″ x 4″ x 6′ (or 8′) length of pine (1) – (cut into four 12″ pieces, see Cut List)
- Wood screws (32) – 2 1/2″ long
- Wood screws (8) – 1″ long
- Corner braces (12 total, 2 in each package) – 2″
- Miscellaneous clamps
- Tape measure
- Wood glue – we swear by Titebond III
- Wood stain – we used FolkArt Home Decor Antiquing Wax
- Goggles to use with your tools
- Small table saw
- Miter saw
- Nail gun with 1 1/4″ nails
- Drill with selection of bits
Cut List – you can download the entire cut list HERE or each page separately: Cut List 1, Cut List 2, Cut List 3. I highly recommend downloading the cut lists and printing to follow along with the instructions. The cut list will help you purchase the right amount of wood assuming you don’t buy the same lengths as listed in the Supplies above.
We learned a lesson on this DIY coffee table project right away! Once you find your pallets, YOUR FIRST STEP needs to be to strip the wood off of the pallet and plane it to a uniform thickness of 1/2″.
Then let it sit for several weeks to dry in a non-humid environment (at least inside a garage or basement) so that the drying doesn’t occur after your table is assembled. We assumed our wood was already dry because it felt dry – we learned the hard way. :0
Step One: Grab your 2 x 2s and trim them down to 30″ pieces. Make 45º cuts at each end using the miter saw (see Fig. 1 on the Cut List).
Step Two: Use the corner braces with your drill to join the 2 x 2s into two frames.
Step Three: Cut down the remaining 2 x 2 wood into 27″ long pieces (see Fig. 3 on the Cut List). You’re going to add two cross pieces to each frame.
Use your tape measure to add them at 10″ and 20″ – so equidistant across the frame on the top and bottom. Mark with a pencil, drill two pilot holes, and then screw in 2 1/2″ wood screws.
If they aren’t EXACTLY at 10″ and 20″ – you’ll be fine. You’ll have two pieces that look like this:
Step Four: Cut your plywood down to 30″ x 30″ using a table saw (or a circular saw – anything you can cut a straight line with, see Fig. 4 on the Cut List).
Attach one of the frames to the plywood (it doesn’t matter which one you pick) using the bottom sides of the corner brackets and your drill. The plywood piece is going to sit on the base of your table, which you’ll make shortly.
Step Five: Cut your 2 x 4 into four 12″ pieces (see Fig. 2 on the Cut List).
Attach the four 12″ pieces as shown in the photo using wood screws and a drill. Notice that the slats on your 30″ top frame are not parallel to the frame on the bottom with the plywood attached. This is on purpose to add some rigidity to the piece.
Step Six: turn the table skeleton over so the plywood base is facing up. You’ll want to have four pieces of pallet wood cut to 3.5″ wide by 22″ long (see Fig. 5 on the Cut List).
We used a table saw to cut the length and the miter saw to quickly cut the ends. Use whatever saw works best for you.
Form your base by making a frame out of the four 22″ pieces. Put wood glue on the end of each board, attach to another board as shown, then nail the ends with the nail gun (see the photo above, left).
Use your remaining corner brackets to add the base to the bottom of the plywood – use your measuring tape to center the base. Then add about eight additional 1″ wood screws to attach the plywood to the frame. Add them in the middle, randomly.
This is how the base looks when it’s done. You can flip the table back over.
Step Seven: Pay close attention as I explain the next part. You now have a skeleton frame of a table, with a base. The next step is to cover the top, then in the following step you’ll cover the sides.
Our table top has two end pieces (shown as Fig. 7 and Fig. 8 on the Cut List) and SIX pieces in between (shown as Fig. 6 on the Cut List) of varying widths. You may or may not have six middle pieces depending on a variety of factors (like how big you decided to make your table or how wide the pieces were to begin with). The two end pieces need 45º angles down three sides – two short sides and one long side – cut with a table saw. The middle pieces need 45º angles on each end.
Steve cut and glued as he went along. He started at one end. He cut the end piece using his table saw (with the 30″ length and the 45º angle), then glued it down with wood glue and clamped it into place.
Then he cut a second pallet board – 30″ long, 45º angles on both ends, glued into place. You don’t need to clamp the second board, just put it in tightly.
Steve varied the width of the pallet boards using the table saw as he went along. You can cut and glue as you go, or you can cut all of the pieces and lay them out first. That’s your choice.
Steve continued cutting and gluing, but not all the way to the end. Once he got close to the end, he did the end piece first, THEN went back and cut the last piece to fit in the remaining gap with his table saw.
Oh, and I should mention, he used weights as he went along too. The weights were paver stones, because they were handy:
Once the table top is done, let it dry for a few hours.
Step Eight: Time for the sides! You’re going to approach the sides the same way you did the top. The differences: the side pieces are shorter (12.5″ long), the end pieces need two sides with 45º angles (instead of three), and the middle pieces only need one short end with a 45º angle instead of both (see Figs. 9 and 10 on the Cut List).
Cut and glue as you did before – the side boards will meet the top boards and the two 45º angles will fit right together. It might not be perfect . . . but it will be close enough for government work, if you know that saying? (tee hee)
Repeat with the other three sides – leaving a couple hours of drying time between sides.
Pretty soon, you’ll have a finished table! You can leave it as is, or you can do a light sanding with 120 grit. We chose to do a light sanding before staining. Wipe away any sanding dust, of course!
You might be asking if the wood glue is enough to hold all four sides and the top on – the answer is yes. We’ve done a lot of sitting and dancing on the table (you think I’m kidding) and it’s really sturdy. You’re in the home stretch!
The last step was to stain and wax the table. We picked FolkArt Home Decor Wax in Antiquing – for several reasons. It’s non-toxic, we liked the color, and it also provides a really smooth finish to the touch because it’s a wax and stain in one.
Just glop it on as shown, then rub in with a cloth. Work about 1/3 of the table top at a time, then the sides, then the base. Don’t leave the wax on for too long before wiping away with the rag because it will soak in.
It’s really amazing how the stain soaks into the pallet wood on our DIY coffee table and gives a beautiful finish . . . with gorgeous variations in color. The nail holes and knots add character as well.
Take a look at the details – we’re so happy with how our DIY coffee table turned out!
Our West Elm inspired DIY coffee table is one of our favorite furniture pieces of all time! AND as I mentioned, total cost of $45 . . . a huge savings over $999.
The pallet wood helped with the cost and also helped with the character. If you want to make something with pallets but aren’t sure where to find them or where to start, check out this article.
You can scale our DIY coffee table to any size, and stain it with any color. I’d love to hear what you think in the comments!
- Small table saw
- Miter saw
- Nail gun with 1 1/4" nails
- Drill with selection of bits
- Tape measure
- Staining rags
- Strip the wood off of your pallets and plane to a uniform thickness of 1/2".
- Grab 2 x 2s and trim them down to 30" pieces. Make 45º cuts at each end using the miter saw.
- Use the corner braces with a drill to join the 2 x 2s into two frames.
- Cut down the remaining 2 x 2 wood into 27" long pieces.
- Add two cross pieces to each frame. Use your tape measure to add them at 10" and 20" - so equidistant across the frame on the top and bottom. Mark with a pencil, drill two pilot holes, and then screw in 2 1/2" wood screws.
- Cut the plywood down to 30" x 30" using a table saw.
- Attach one of the frames to the plywood (it doesn't matter which one you pick) using the bottom sides of the corner brackets and your drill.
- Cut the 2 x 4 into four 12" pieces.
- Attach the four 12" pieces as shown in the photo using wood screws and a drill.
- Turn the table skeleton over so the plywood base is facing up.
- Cut four pieces of pallet wood to 3.5" wide by 22" long.
- Form a base by making a frame out of the four 22" pieces. Put wood glue on the end of each board, attach to another board as shown, then nail the ends with the nail gun.
- Use the four remaining corner brackets to add the base to the bottom of the plywood - use a measuring tape to center the base.
- Add about eight additional 1" wood screws to attach the plywood to the frame. Add them in the middle, randomly.
- Cut pallet wood to fit the table top. Cut the end pieces first. The two end pieces need 45º angles down three sides - two short sides and one long side - cut with a table saw. The middle pieces need 45º angles on each end.
- Vary the width of the boards. As the boards are cut, glue them down.
- Let the table top dry for several hours.
- Cut the side pieces. The side pieces are shorter (12.5" long), the end pieces need two sides with 45º angles (instead of three), and the middle pieces only need one short end with a 45º angle instead of both.
- Cut and glue as you did from step 16. Repeat with the other three sides.
- Do a lightsanding with 120 grit sandpaper. Wipe away the sanding dust.
- Stain and wax the table; let dry for several hours before using.