Make a mid-century inspired DIY wood doormat using wood slats and your favorite retro fabric! It’s easier to do than you think, and it’s really unique.
My boyfriend and I are huge fans of mid-century modern home decor items. We are especially inspired by the color palettes; greens, browns, oranges . . . shades along these lines.
For me, it’s a reminder of my grandparents’ house in Bellevue, WA, just outside of Seattle. My dad grew up in this home in the 1960s, and when I was growing up the furniture was the same.
I’d like to tell you that my grandparents were stylish, but I think they just didn’t want to buy anything new. Either way, I have a fondness for Mad Men-esque furniture, and it’s the look we go for in our home, at least a version of it.
Our latest creation inspired by mid mod is this DIY wood doormat. We knew we wanted to make a wood slated welcome mat, and I actually had the fabric from a previous project. Steve saw the fabric and like it, and then the rest just came together. Here’s how we made it.
Make Wood Doormat
Gather These Supplies
- Two 8-foot 1 x 2s – cut into fifteen 18 inch pieces (these will be your slats)
- Mod Podge Outdoor
- Thompson’s Water Seal – Nutmeg
- FolkArt Multisurface paint – Pure Orange
- Clear outdoor spray sealer – I believe we used Rustoleum
- Fabric – pattern of your choice
- Wood beads – 42 total, 3/4″ round
- Nylon cord – around 13 feet (make sure it fits through your beads)
- Paint brush
- Craft knife and mat
- Wax paper
- Table saw
- Tape measure
Note: Steve used oak for this. He also stained the slats with Thompson’s Water Seal and a foam brush after cutting, then let dry.
The next step, which we didn’t get a photo of, was drilling into the slats. He measured holes at 2.5″, 9″, and 15.5″ inches on the side of each slat (in the center from top to bottom) – then made a pencil mark.
Use a drill bit that matches the hole in your wood beads. Not all wood beads have the same sized hole, so you’ll need to use the drill bit that works for your beads.
Mod Podge Outdoor can be REALLY thick to work with. My suggestion is to dip your brush in water and use that to stir up the Podge before application.
You can do this outside of the jar as well. You don’t want to add too much water; dipping my brush in always seems to be just enough without diluting. Let your fabric dry.
And if you’re wondering why I’m preparing the fabric with Mod Podge? You’ll see when I trim the fabric.
It can be hard to paint (and annoying) to paint wood beads. Using a dowel rod helps. Slide the beads onto the dowel while painting.
This is part of the reason why I prepped the fabric with Mod Podge. I cut a piece of fabric slightly larger than each slat with the scissors. Your fabric won’t fray during this step because you prepared it (and there’s an even better reason coming up).
Repeat for each slat.
Work one slat at a time, applying Fabric Mod Podge . . .
Then I turned each slat over and used the brayer to completely smooth it out. Wipe away any Mod Podge that squeezes out the sides between the fabric and slat with a brush.
Repeat with the rest of the slats and let dry for an hour or so.
NOW you’ll know why I prepared the fabric. Place each slat onto a cutting mat and trim the excess fabric off with a craft knife. It’s a HUGE pain in the butt if you didn’t prep the fabric! It’s much easier to cut (it cuts like paper) if you do the preparation stage. At least that’s my experience.
Repeat with the rest of the slats.
Coat them all with Fabric Mod Podge and let dry.
then pulled taut to tie knots at the end. He trimmed with scissors and then melted slightly with a lighter to seal.
Your final step is to spray the entire thing with the clear acrylic sealer, several coats, to reduce tackiness from the Mod Podge and add further protection.
What do you think of this wooden doormat? Are you a fan of mid-century inspired style? We’d love to see your projects!